seagate seatools serial number doesnt match

#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH SERIAL NUMBERS#
#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH FULL#
#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH SOFTWARE#
#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH WINDOWS#

Unless the drive is full of data, it is quite possible for the problem sector to be empty of data, anyway. When SeaTools reallocates these problem sectors the actual data in a particular sector is unreadable and already lost. Be sure that you have all of your data backed up before running any of the “Fix All” tests. There are two options with the “Fix All” tests, “Fast” and “Long”. The “Fix All” tests provide the ability to fix problem LBA’s (bad sectors).

#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH SOFTWARE#

The apparent lack of activity often gives the impression that the drive or software has stopped responding. Because the long tests read every sector on the drive, the amount of time required will depend on the speed and capacity of the disk drive. The long tests will take time to complete. If you need a more comprehensive test then consider running the “Long Generic”, which reads each sector on the drive. The 'Short Drive Self Test' is adequate for most situations. The “Short Generic” test is similar and tests various areas of the drive. When you launch the 'Short Drive Self Test' (DST) most drives will run a thorough diagnostic routine that is built into the hard drive's firmware. Long Generic (progress in 1% increments and may take several hours to complete).Short Drive Self Test (20 to 90 seconds long).Select the tests that you would like to perform.

All Basic Tests are data safe, read-only tests. You may select more than one drive at a time to test them simultaneously.Ī menu of the possible diagnostic tests is shown. Non-Seagate drives have a silver drive icon Seagate, Samsung, LaCie and Maxtor drives models are given a gold drive icon. (For help on finding the model number of a drive, please see our ' Find Your Model and Serial Numbers' Knowledge Base article.)

#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH WINDOWS#

However, Seatools for Windows often displays the serial number and even the model number of the internal drive inside the external case, and these numbers do not correspond to the numbers that Seagate assigns to the external unit as a whole.

#SEAGATE SEATOOLS SERIAL NUMBER DOESNT MATCH SERIAL NUMBERS#

Seagate serial numbers are alphanumeric and eight characters long. Seagate model numbers begin with the letters 'ST'. This screen also displays information about the drives such as the Model Number and Serial Number. Select the drive you would like to test by making a check mark in the box next to the drive information. Be sure to connect the AC adapter to ensure adequate power during the tests.Īfter SeaTools loads, the screen will list the different storage devices in your system. These tests are disk-intensive and will draw more current than a typical usage profile.

Plug in your laptop computer - Laptop systems should not run the long tests using just battery power.

The setting ' Turn off hard disks' should be set to ' Never' while running any SeaTools for Windows test.

Click on the Start or Windows icon button in the bottom left corner of your Windows desktop.

The drive is working on its own at these times and the system may decide it should go into Standby or Hibernate modes.

A complete drive scan may take a few hours to complete.

Keep the computer fully powered on - Power management controls may need to be suspended while doing very long tests.

Most desktop and notebook systems have one SATA or PATA internal drive. Internal drives are identified as PATA (Parallel ATA or IDE), SATA (Serial ATA), SCSI, or SAS (Serial-Attached SCSI).

SeaTools' Drive Identification - External drives that connect to the system through USB, 1394 Firewire, or eSATA do not have the same background activity as the internal drive.

This is harmless to the drive and a routine condition of use however, it causes the SeaTools tests to take much longer time to complete. This is harmless to the drive and a routine condition of use however, it causes the SeaTools tests to take much longer time to complete. When that happens, SeaTools will temporarily suspend its current progress while the drive is busy. Otherwise, Windows will continue to give the disk drive commands to access data for the needs of the other applications. The main reason for this is to keep the drive focused on SeaTools as much as possible.

Isolate SeaTools - close all other applications before running a hard disk diagnostic.

If you have a SeaTools for Windows icon on your desktop, simply launch the program from here. Launch SeaTools by following these steps once it is installed:

Seagate seatools serial number doesnt match